Imported bar cutting machine for TMT bar up to 32 mm, 3 kW motor, about 2 seconds per cut, 365 kg.
Starting from ₹65,000 Plus GST. Ex-works Delhi.
Today's price ₹65,000 Ex-works Delhi. Final price depends on configuration.
Not sure this is the right size?
Tell us the material, the area and the specification you have to meet. We will tell you which machine fits — and which one is more than you need.
The GQ40H is an imported electric bar cutting machine rated for TMT bar up to 32 mm. A 3 kW motor drives the flywheel and crank, the blade completes a cut in about 2 seconds, and the 365 kg body keeps the machine planted while it does so. It is the cutter that pairs with a 32 mm bender in most building-site bar yards.
Contractors buy it to stop cutting bar with abrasive wheels. A cut-off wheel is slow, burns the bar end, throws sparks near timber and stores, and needs a new disc every few dozen cuts. A shear cutter gives a square, cold cut in two seconds, and the only consumable is a blade that lasts for thousands of cuts.
Supplied, commissioned and serviced by Topall Impex from Delhi, with blades and electrical spares in stock.
Both imported cutters have a 32 mm cutting range and take about 2 seconds a cut. The GQ40H does it on 3 kW at 365 kg, on a 1200 × 400 × 700 mm frame; the GQ50 needs 4 kW and weighs 480 kg. If the machine cuts one site's schedule, the GQ40H does the job and costs less to buy and move. The GQ50 is bought for continuous full-shift cutting of large bar in a central yard, where its extra kilowatt and 115 kg keep the cut clean hour after hour.
The Indian-made TCM-42 is the other 32 mm option, with a 5 HP motor and a cast body at a lower price. The GQ40H is the imported choice at the same capacity.
The cutting rate is set by the crank, not the operator, so throughput comes down to feeding. With a measuring stop and a helper on the bar rack, one machine keeps a full bending crew supplied. Cut only single bars at the rated diameter; stacking small bars to save time is what chips blades.
The 3 kW motor runs at 2880 rpm on a 415 V three-phase supply. The flywheel stores the energy for each cut, so the motor is not heavily loaded and the machine tolerates generator supply better than a bender does.
Delivery, commissioning at site and operator handover on blade setting and the measuring stop. Blades, belts and contactors are stocked in Delhi.
| Specification | GQ40H |
|---|---|
| Cutting Range | 32 mm |
| Cutting Time | 2 / sec |
| Power | 3 kW |
| Speed | 2880 rpm |
| Voltage | 415 V |
| Weight | 365 kg |
| Dimension | 1200 × 400 × 700 mm |
Specifications as published in the Topall Impex catalogue. Configurations can vary — confirm with our team before ordering.
Topall ke machines ka biggest benefit mujhe project productivity mein dikha. Site requirement ke according machine select karne mein team ne support kiya aur installation ke baad operators ko proper briefing mili.
Construction machinery mein purchase ke saath after-sales bhi equally important hota hai. Topall ke case mein commissioning aur operator training properly mili. Spare availability ke baare mein bhi team clear thi, isliye overall experience positive raha.
Humne Topall se different categories ki machines dekhi aur requirement ke according model select kiya. Sales team ne sirf expensive model push nahi kiya, site requirement samajhkar option suggest kiya. Ye approach achhi lagi.
Topall ke saath mera experience sirf machine delivery tak nahi raha. Machine site par commission karna aur operator ko practically samjhana unka strong point laga. Equipment lene ke baad confidence raha ki issue aaye to support available hai.
Tell other contractors how this machine performed on your site.
Other machines that do the same job at a different size or output — useful if this one is more, or less, than your site needs.
