Magnesium bull float, 1200 × 200 mm blade on three 1800 mm stainless steel handles, for closing a freshly screeded slab.
Starting from ₹9,500 Plus GST. Ex-works Delhi.
Today's price ₹9,500 Ex-works Delhi. Final price depends on configuration.
Not sure this is the right size?
Tell us the material, the area and the specification you have to meet. We will tell you which machine fits — and which one is more than you need.
The FBF33 is a magnesium bull float, the tool that goes over a slab immediately after it has been screeded. Its 1200 × 200 mm blade is pushed and pulled across the surface on three stainless steel handles of 1800 mm each, knocking down the ridges the screed leaves, filling the small hollows and bringing enough paste to the surface for the later floating and trowelling passes, without sealing the slab so early that bleed water gets trapped underneath.
Magnesium matters here. A wooden float drags and tears; a steel float seals the surface too soon. Magnesium is light, slides on fresh concrete, and opens the surface just enough.
Handles and replacement blades are held in Delhi, with support from Mumbai, Ahmedabad, Hyderabad and Chennai.
The FBF33 is a plain float, worked by hand. The Beton Trowel Vibra Tamp bull float adds vibration to the blade, so it consolidates and closes the surface in fewer passes on stiffer mixes. For ordinary slab work and slump concrete the FBF33 is the right tool and the cheaper one; move to the Vibra Tamp when mixes are stiff, fibre-dosed or written to a tight flatness figure.
The three 1800 mm handles join to give 5.4 m of reach, and being stainless steel they do not rust after years of daily wash-downs. On a 6 m wide pour the float has to reach 3 m from either edge, which the full handle set covers with an operator on each side. Keep the handle angle low on the push stroke and lift the leading edge slightly on the pull, or the float digs in and leaves a line. Rinse the blade before the paste sets on it.
The FBF33 is the first of three hand tools that belong together. After bull floating and once the bleed water has evaporated, the FCR33 check rod finds the high and low spots and the FBC33 bump cutter takes the highs down; both are 3 m aluminium alloy straightedges on the same stainless steel handles. Buy them as a set; a floor floated but never checked is where flatness complaints start.
The float blade, bracket and three 1800 mm stainless steel handles, delivered from Delhi. Spare handles and blades are stock items. Ask us for a slab-finishing kit if you are also buying a power trowel.
| Specification | FBF33 |
|---|---|
| Blade Size | 1200 × 200 mm |
| Handle Length | 1800 mm per piece |
| No. of Handles | 3 |
| Material of Blade | Magnesium |
| Material of Handle | Stainless Steel |
| Drive Mode | Manual pull / push |
| Bracket | Included |
Specifications as published in the Topall Impex catalogue. Configurations can vary — confirm with our team before ordering.
Topall ke machines ka biggest benefit mujhe project productivity mein dikha. Site requirement ke according machine select karne mein team ne support kiya aur installation ke baad operators ko proper briefing mili.
Construction machinery mein purchase ke saath after-sales bhi equally important hota hai. Topall ke case mein commissioning aur operator training properly mili. Spare availability ke baare mein bhi team clear thi, isliye overall experience positive raha.
Humne Topall se different categories ki machines dekhi aur requirement ke according model select kiya. Sales team ne sirf expensive model push nahi kiya, site requirement samajhkar option suggest kiya. Ye approach achhi lagi.
Topall ke saath mera experience sirf machine delivery tak nahi raha. Machine site par commission karna aur operator ko practically samjhana unka strong point laga. Equipment lene ke baad confidence raha ki issue aaye to support available hai.
Tell other contractors how this machine performed on your site.
Other machines that do the same job at a different size or output — useful if this one is more, or less, than your site needs.
