Bar bending machine price in India spans a wide range. A basic manual or motorised bar bender sits under Rs 1 lakh. A semi-automatic stirrup bender runs a few lakh. A fully automatic CNC stirrup bending machine costs about Rs 14 lakh to Rs 37.4 lakh depending on wire diameter capacity and whether it bends single or double wire.
Why bar bending machine prices vary so much
The phrase "bar bending machine" covers three completely different machines — and whether the listing says steel bar bending machine, TMT bar bender or rebar bender, the classes underneath are the same three. Comparing their prices without saying which one you mean is how contractors end up disappointed.
Manual and motorised bar benders. One operator, one bar at a time, angle set by a stop. Cheap to buy, cheap to run, slow. Fine for a small site or a repair contractor. In the open market, hand benders cost a few thousand rupees and motorised benders stay under Rs 1 lakh. We do not sell this class — if it is all your site needs, our guide to bar bender: hand tool vs machine will tell you so honestly.
Semi-automatic stirrup benders. Feed is assisted, angles are repeatable, but a person still handles each piece. Middle of the range on both price and output — quotes vary too widely by make to put one honest number on, which is itself worth knowing before you compare two of them.
CNC automatic stirrup bending machines. Steel goes in from a coil or bundle, finished stirrups come out to a programmed drawing. This is the class sold as "fully automatic", and it is where the price jumps and where the economics change completely.
Fully automatic bar bending machine price in India (CNC)
| Machine | Single wire | Double wire | Output | Indicative price |
|---|---|---|---|---|
| GTD4-10S automatic stirrup bender | 4 – 10 mm TMT | — | 2,000 pcs/hr | Rs 14,00,000 – Rs 15,40,000 |
| GTD5-12D automatic stirrup bender | 4 – 12 mm TMT | 4 – 10 mm TMT | 2,400 pcs/hr | Rs 34,00,000 – Rs 37,40,000 |
So a working answer to "fully automatic bar bending machine price in India" is Rs 14 lakh to Rs 37.4 lakh ex-works Delhi, and which end you need is decided by wire count and bar diameter, not by budget. The gap between the two is not a size upgrade. The GTD5-12D bends two wires at once and handles 12 mm single wire. If your bar schedule is mostly 8 mm and 10 mm stirrups in high volume, double-wire capability roughly doubles throughput for the same floor space and one operator. The full range lives on our bar bending machine page.
The number that actually matters: cost per stirrup
A machine at Rs 14 lakh looks expensive next to a Rs 80,000 bender. Then you count.
A CNC machine producing 2,000 stirrups an hour with one operator replaces a bending gang. It also removes the two costs nobody puts in the quote:
- Steel wastage. Hand bending to a drawing produces off-cuts and rejects. A programmed machine cuts to length from the schedule. On a large job the steel saved is a real number.
- Rework. Stirrups outside tolerance get rejected at inspection. A machine holding plus or minus 1 mm length tolerance does not generate that argument.
Work out your monthly stirrup requirement, your current gang cost, and your wastage percentage. If you are producing in the tens of thousands of pieces a month, the payback period on a CNC machine is usually measured in months, not years.
What to check before you buy
Bar diameter range, both ends
Everyone checks the maximum. Check the minimum too. A machine rated 6 to 12 mm will not handle 4 mm cleanly, and small-diameter stirrups are common in slab and column ties.
Bending angle tolerance
Ask for the published figure. Plus or minus 1 degree is a real specification. "Accurate" is not.
Power supply
CNC stirrup machines need a stable three-phase supply. A GTD4-10S draws around 4.5 KW average with 20 KW rated total power. Check what your yard can actually deliver before the machine arrives.
Who commissions it
A CNC bender set up wrong produces scrap fast. Installation and operator training should be part of the supply, not an extra.
Who you are buying from
The price on the quote matters less than whether spares and service exist behind it. Our guide to bar bending machine manufacturers in India shows how to tell a factory-backed supplier from a trader with a brochure.
Manual versus automatic: a straight answer
If you bend a few hundred stirrups a week, buy a manual bender. The CNC machine will sit idle and the capital is better spent elsewhere.
If you bend thousands a week, run more than one site, or you are supplying a precast or RMC operation, the CNC machine is not a luxury. It is the only way to hold schedule and tolerance without a large, skilled, expensive gang. Send us your bar schedule and you will have a same-day quotation with the machine we would actually put in your yard.
Bar bending machine price FAQs
What is the price of a fully automatic bar bending machine in India?
Rs 14 lakh to Rs 37.4 lakh ex-works Delhi for CNC stirrup bending machines, depending on wire count (single or double) and bar diameter range (4–12 mm TMT). Freight and GST are extra.
What does the cheapest bar bending machine cost?
A hand bender costs a few thousand rupees and a motorised bender stays under Rs 1 lakh in the open market. They bend one bar at a time — fine for small sites, a bottleneck beyond that.
Is a steel bar bending machine different from a TMT bar bending machine?
No. Steel bar, TMT, sariya and rebar are the same deformed steel bar by different names, and the same machine bends them all. What matters is bar diameter and daily volume.
Can I get a bar bending machine price list?
Yes — the table above is current ex-works Delhi pricing, and we send a model-wise quotation the same day. Share your bar sizes and monthly stirrup volume and we will also say which machine you do not need.
Frequently Asked Questions
What is the price of a bar bending machine in India?
What is the price of a fully automatic bar bending machine in India?
How many stirrups per hour can an automatic machine produce?
What bar diameters can these machines bend?
Is a CNC stirrup bending machine worth it for a mid-size contractor?
What power supply does a CNC stirrup bender need?
Machines Covered in This Guide
Get a price for your job
Tell us the material, the area and the specification you have to meet. We will come back with the right machine, the price and the delivery date — usually the same working day.